Audi OEM Head Unit Pinouts

Match the Audi part number, infotainment option and connector ID to the fitted unit before using these pinouts. Connector illustrations identify the viewing side where the reference specifies it.

MMI and navigation

Audi (2005-2012) A4, A5, A6 MMI basic plus Unit and misc connectors

The drawing and connector IDs below follow the A4 B8 workshop configuration. Verify the build and connector IDs on A5 and A6. Part number 4F0910769F is listed in the index with uncertain fitment.

J523 · MMI Basic Plus main connector

12345678910111213141516B172839410511612C172839410511612AD
Rear of J523, redrawn from the A4 workshop illustration. A uses positions 1–8 and D uses 9–16 in the upper bank. B is lower left and C is lower right.

The index groups positions 11–16 under A. The Audi workshop illustration identifies those positions as block D.

Block A · T8ab

J523 terminal face, as viewed at the rear of the unit. The outline identifies block A for the table below.
Cavity Function
1 Wake signal to E380
4 HU reset to E380
5 BT reset to E380
8 Ground to J685 display

Block B · T12q

J523 terminal face, as viewed at the rear of the unit. The outline identifies block B for the table below.
Cavity Function
1 Data sent to E380
3 Positive data to J685
4 Negative data to J685
5 Data received from E380

Block C · T12r

J523 terminal face, as viewed at the rear of the unit. The outline identifies block C for the table below.
Cavity Function
5 Negative data from J685
7 Ground to E380
11 Positive data from J685

Block D · upper positions 9–16

J523 terminal face, as viewed at the rear of the unit. The outline identifies block D for the table below.
Cavity Function
11 Telephone audio mute input
12 Ground, terminal 31
13 Power feed to J685 display
14 Ring-break diagnostics
15 Battery positive, terminal 30
16 Power feed to E380 control panel

J685 display · 10-pin T10t

16273849510
Rear-of-display view from Audi workshop drawing A91-10052. Pin 1 is upper left and pin 6 is directly below it.

Display power discrepancy. The index lists pin 1, while the A4 B8 workshop manual lists pin 2. Verify the fitted display and wiring diagram before applying power.

Cavity Function
2 Display power from J523, per Audi A4 workshop manual
3 Ground from J523
6 Ground, terminal 31
7 Positive data from J523
8 Negative data from J523
9 Positive data to J523
10 Negative data to J523

R41 MMI CD changer · 8-pin electrical connector

75318642
R41 electrical connector, drawn in the numbering orientation shown in the MMI Basic Plus reference.
75318642
Rear view from the Audi Q5 R41 service illustration A91-12116, showing the recess around the purple electrical socket.
Cavity Function
1 Ground, terminal 31
2 Battery positive, terminal 30
4 Ground, listed for MMI Basic only
5 Ring-break diagnostics

E380 multimedia controls · 16-pin T16c

19210311412513614715816
Audi workshop drawing A91-0908, viewed into the E380 socket. Pin 1 is upper left and pin 9 is directly below it.
Cavity Function
6 Wake signal
7 Power supply
8 Ground
13 HU reset
14 BT reset
15 Data input
16 Data output
Audi A6/S6/RS6 C5 and A4 · RNS-E Navigation Plus

Aisin RNS-E · Audi A6/S6/RS6 C5 part 4B0 035 192 P (Aisin 86113-60V110). The photographed factory label for A4 part 8E0 035 192 Q shows the same assignments. Match the suffix on the installed radio. Separate R8 and TT radios have their own part numbers.

Assignments for both part numbers follow the Aisin radio labels. Terminal 30 is D15 and terminal 31 is D12. DSP wake at D13, the CD-changer supply and the 32-way analogue inputs have separate functions. Only labelled signals are listed.

15 AA15263748D913101411151216B123456789101112C123456789101112
RNS-E housing in the factory label orientation (rotated 180°).

A · front speakers

RNS-E socket viewed from the rear of the radio · block A.
Cavity Function
2 Right front speaker +
3 Left front speaker +
6 Right front speaker −
7 Left front speaker −

B · CD changer and external control

RNS-E socket viewed from the rear of the radio · block B.
Cavity Function
1 MOST ring-break signal
2 CD changer audio ground
3 Vehicle-speed signal
4 CD changer supply (U14R-2)
5 K-line diagnostics
6 CD changer data out
7 BOSE coding
8 CD changer left audio input
9 CD changer right audio input
10 CD changer switched supply (U14 ST CDC)
11 CD changer data in
12 CD changer clock

C · line output, telephone and microphone

RNS-E socket viewed from the rear of the radio · block C.
Cavity Function
1 Microphone input −
2 Reverse signal (RFSL)
3 Front left line output
4 Microphone output −
5 Rear left line output
6 Telephone audio input −
7 Microphone input +
8 Line-output ground
9 Front right line output
10 Microphone output +
11 Rear right line output
12 Telephone audio input +

D · power, CAN and amplifier control

RNS-E socket viewed from the rear of the radio · block D.
Cavity Function
9 Infotainment CAN high
10 Infotainment CAN low
11 Telephone mute
12 Ground (terminal 31)
13 DSP wake / radio-on output
14 Anti-theft alarm ground
15 Permanent +12 V battery supply (terminal 30)
16 U14R-1 (as marked on the label)

32-way accessory and video input

1234567891011121314151617181920212223242526272829303132
RNS-E 32-way socket · rear of radio.
1234567891011121314151617181920212223242526272829303132
RNS-E 32-way connector · factory-label orientation (rotated 180°).
Cavity Function
6 AUX right audio input
13 Right audio input
14 Shield ground
15 Video sync input
16 Green video input
21 AUX audio ground
22 AUX left audio input
28 Audio input ground
29 Left audio input
30 RGB/sync ground
31 Blue video input
32 Red video input
Audi (2008-2015) Q5, Q7 MMI 3G (3G+) Unit

Part numbers listed: 4L0035646 (minimal), 4L2035670G, 8R1035670M (maximal)

Variant check. The Block A source repeats cavity 6 with reset descriptions. Confirm the reset wiring on the applicable minimum, intermediate or maximum equipment version. A single listed description is shown as supplied where the source gives no separate option values.

16 pin A connector

12345678910111213141516AFUSEB172839410511612C172839410511612
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Minimum Intermediate Maximum Single source assignment
1 LF mute from preliminary setup for cell phone preparation N/C LF mute from preliminary setup for cell phone preparation —
2 — — — Voltage supply to Multimedia Control Head
3 — — — Wake UP to multimedia system control head
5 N/C N/C Switch-on signal for the Cellular Telephone Amplifier —
6 — — — Reset to the Multimedia System Control Head
7 — — — Ring-break diagnostic cable
9 N/C N/C Switch-on signal to Telephone Baseplate —
10 — — — Data from multimedia system control head
11 — — — Data to the multimedia system control head
12 — — — Ground (terminal 31)
13 N/C N/C DIAG signal from Telephone Baseplate —
14 — — — Reset from multimedia system control head
15 — — — Permanent power (terminal 30)
16 — — — Ground (GND) to multimedia system control head

12 pin B connector (blue)

12345678910111213141516AFUSEB172839410511612C172839410511612
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Minimum equipment Higher equipment
2 — Microphone IN (+) for the microphone unit in front roof module (Right)
3 — Microphone IN (-) for the microphone unit in front roof module (Right)
5 — CVBS wire (-) from Rear View Camera System Control Module
8 Microphone IN (+) for the microphone unit in front roof module Microphone IN (+) for the microphone unit in front roof module (Left)
9 Microphone IN (-) for the microphone unit in front roof module Microphone IN (-) for the microphone unit in front roof module (Left)
11 — CVBS wire (+) from Rear View Camera System Control Module

12 pin C connector (green)

12345678910111213141516AFUSEB172839410511612C172839410511612
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 LF-In ground
2 Right LF-In
3 USB (+5V)
4 USB (ground)
6 Detect
7 Left LF-In
8 LF-In ground shielding
9 CVBS cable (+)
10 CVBS cable (-)
11 iPod data
12 iPod data

4 pin display unit Connector

Audi Q5 8R J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.

Display pin 2 varies. T4al uses LIN on the documented configuration. Audi lists pin 2 as unused on the grey T4am configuration.

Cavity Function
1 LVDS (-)
2 LIN
3 LVDS(+)
4 ground

4 pin USB Connector

Audi Q5 8R J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D+
2 iPod detected
3 D-
4 ground
Audi (2008-2015) RNS-E A3, TT Navigation Head unit

Part numbers listed: 8J0035193F, 8J0035193FX, 8P0035192S?

Connector block A

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
A9 CAN Bus High (Infotainment)
A10 CAN Bus Low (Infotainment)
A11 NF mute (audio) from pre-fitted components for mobile phone installation
A12 Ground (terminal 31)
A13 Switched positive to digital sound package control unit
A15 Permanent power (terminal 30)

Connector block B

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
B2 Signal ground to CD changer / iPod holder
B4 Permanent live to CD changer / iPod holder
B6 Data output to CD changer / iPod holder
B7 BOSE coding to ground
B8 Signal (left-side) from CD changer / iPod holder
B9 Signal (right-side) from CD changer / iPod holder
B10 Switched positive to CD changer / iPod holder
B11 Data input from CD changer / iPod holder
B12 CLK (clock) from CD changer / iPod holder

Connector block C

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
C1 Microphone input (–) from microphone unit in front roof module
C3 Signal (front left) to digital sound package control unit
C4 Microphone output (–) to telephone transmitter and receiver unit / pre-fitted components for mobile phone installation
C5 Signal (rear left) to digital sound package control unit
C6 NF– (audio) from telephone transmitter and receiver unit / pre-fitted components for mobile phone installation
C7 Microphone input (+) from microphone unit in front roof module
C8 Signal ground to digital sound package control unit
C9 Signal (front right) to digital sound package control unit
C10 Microphone output (+) to telephone transmitter and receiver unit / pre-fitted components for mobile phone installation
C11 Signal (rear right) to digital sound package control unit
C12 NF + (audio) from telephone transmitter and receiver unit / pre-fitted components for mobile phone installation

RNS-E 32-pin AV/TV input connector

Harness insert, wire-entry view with the grey lever shell removed. The installation drawing identifies pin 1 at the lower right in this orientation.
Cavity Function
6 Analog input · right-side (audio) from connection for external audio sources
13 Audio input, right from TV tuner
14 Screen ground from TV tuner
15 Video input sync. from TV tuner
16 Video input, green from TV tuner
21 Analog input · ground (audio) from connection for external audio sources
22 Analog input · left-side (audio) from connection for external audio sources
28 Audio ground from TV tuner
29 Audio input, left from TV tuner
30 Video ground from TV tuner
31 Video input, blue from TV tuner
32 Video input, red from TV tuner
Audi (2008-2016) A4, A6, S6 C6 4F CD Navigation Basic Unit

Part numbers listed: 4F0035769B, 4F0035769

16 pin A connector

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Wake UP to Multimedia System Control Head
4 Res HU to multimedia system control head
5 Res BT to multimedia system control head
6 Ground (GND) to multimedia system control head
11 NF mute from preliminary setup for cell phone preparation
12 Ground (terminal 31)
13 Voltage supply for the front information display control head
14 Ring-break diagnostic cable
15 Permanent power (terminal 30)
16 Voltage supply to Multimedia System Control Head

12 pin B connector

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Data to the multimedia system control head
3 Data (+) to Front Information Display Control Head
4 Data (-) to Front Information Display Control Head
5 Data from multimedia system control head

12 pin C connector

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
5 Data (-) from Front Information Display Control Head
7 Ground (GND) to Multimedia Control Head
11 Data (+) from Front Information Display Control Head
Audi (2008-2016) A4, S4 8K MMI Navigation Head Unit

minimum and maximum equipment

16 pin A connector

Audi J794 connector orientation. The upper 1–16 bank includes Audi blocks A (1–8) and D (9–16). Check the fitted specification.
Cavity Minimum equipment Maximum equipment
1 NF mute from preliminary setup for cell phone preparation NF mute from preliminary setup for cell phone preparation
2 Voltage supply to Multimedia Control Head Voltage supply to Multimedia Control Head
3 Wake UP to multimedia system control head Wake UP to multimedia system control head
5 — Switch-on signal for the cellular telephone amplifier
6 Res MU to multimedia system control head Res MU to multimedia system control head
7 Ring-break diagnostic cable Ring-break diagnostic cable
9 — Switch-on signal to telephone base plate
10 Data from multimedia system control head Data from multimedia system control head
11 Data to the multimedia system control head Data to the multimedia system control head
12 Ground (terminal 31) Ground (terminal 31)
13 — Telephone base plate DIAG signal
14 Res BT from multimedia system control head Res BT from multimedia system control head
15 Permanent power (terminal 30) Permanent power (terminal 30)
16 Ground (GND) to multimedia system control head Ground (GND) to multimedia system control head

12 pin B connector

Audi J794 connector orientation. The lower inserts are B on the left and C on the right. Check the fitted specification.
Cavity Minimum equipment Maximum equipment
2 — Microphone IN (+) for the microphone unit in front roof module
3 — Microphone IN (-) for the microphone unit in front roof module
5 — FBAS wire (-) from Rear View Camera System Control Module
8 Microphone IN (+) for the microphone unit in front roof module (left front microphone) Microphone IN (+) for the microphone unit in front roof module (left front microphone)
9 Microphone IN (-) for the microphone unit in front roof module (left front microphone) Microphone IN (-) for the microphone unit in front roof module (left front microphone)
11 — FBAS wire (+) from Rear View Camera System Control Module

12 pin C connector

Audi J794 connector orientation. The lower inserts are B on the left and C on the right. Check the fitted specification.
Cavity Function
1 LF-In ground
2 Right LF-In
3 USB (+5V) to the internet access control module (2013 year or later)
4 USB (ground)
6 Detect to the internet access control module (2013 year or later)
7 Left LF-In
8 LF-In ground shielding
9 FBAS wire (+)
10 FBAS wire (-)
11 iPod data
12 iPod data

4 pin display unit Connector (purple)

Audi A4 B8 J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.

Display pin 2 varies. T4al uses LIN on the documented configuration. Audi lists pin 2 as unused on the grey T4am configuration.

Cavity Function
1 LVDS (-)
2 LIN
3 LVDS(+)
4 ground

4 pin USB Connector (yellow)

Audi A4 B8 J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D+
2 iPod detected
3 D-
4 ground
Audi (2011-2014) A6, C7 Low MMI Navigation

Part numbers listed: 4G0035192H, 4G0035192F

52-position main housing · block A

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block A is highlighted.
Cavity Function
A1 rear right speaker +
A2 front right speaker +
A3 front left speaker +
A4 rear left speaker +
A5 rear right speaker –
A6 front right speaker –
A7 front left speaker –
A8 rear left speaker –
A9 Subwoofer (+)
A10 Centre speaker (+)
A13 Subwoofer (-)
A14 Centre speaker (-)
A17 Ground (terminal 31)
A18 Permanent power (terminal 30)

52-position main housing · block B

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block B is highlighted.
Cavity Function
B1 Data from multimedia system operating unit
B2 RES BT multimedia system operating unit
B4 Microphone input (+) from microphone unit in front roofmodule, front left microphone
B5 FBAS wire (-) from reversing camera system control unit
B6 DIAG signal from telephone bracket
B7 Data to multimedia system operating unit
B8 Wake-up multimedia system operating unit
B9 Res HU to multimedia system operating unit
B11 FBAS wire (+) from reversing camera system control unit
B12 Microphone input (–) from microphone unit in front roof module front left microphone

52-position main housing · block C

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block C is highlighted.
Cavity Function
C1 Analog input · ground (audio)
C2 Analog input · right-side (audio)
C3 USB (+5 V)
C4 USB (ground)
C6 Detect
C7 Analog input · left-side (audio)
C8 Analog input · screen ground (audio)
C9 FBAS wire (+)
C10 FBAS wire (–)
C11 iPod data
C12 iPod data

52-position main housing · block E

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block E is highlighted.

The A6 4G RMC service table lists the ring-break circuit at E7. Confirm E12 with the wiring diagram for the fitted telephone equipment.

Cavity Function
E7 Ring-break diagnostics
E12 Switch-on signal to telephone bracket

4 pin light-brown connector

Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D (+)
2 iPod detected
3 D (–)
4 ground

4 pin purple connector

Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground
Audi (2011-2016) A8, S8 MMI Multimedia CD Player

Part numbers listed: 4H0 035 746 D, 4H0 035 746 E, 4H0 035 746 F, 4H0 035 746 G, 4H0 035 746 H, 4H0 035 746 J, 4H0 035 746 K

16 pin A connector

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
3 Wake-up to multimedia system operating unit
5 Switch-on signal to aerial amplifier for mobile telephone
6 Res MU to multimedia system operating unit
7 Ring-break diagnostics
9 Switch-on signal to telephone bracket
10 Data from multimedia system operating unit
11 Data to multimedia system operating unit
12 Terminal 31 (ground)
13 DIAG signal from telephone bracket
14 Res BT from multimedia system operating unit
15 Permanent power (terminal 30)

12 pin B connector

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
2 Microphone input (+) from microphone unit in front roof module (front right microphone for LHD vehicle)
3 Microphone input (–) from microphone unit in front roof module (front right microphone for LHD vehicle)
5 FBAS wire (-) from reversing camera system control unit
8 Microphone input (+) from microphone unit in front roof module (front left microphone for LHD vehicle)
9 Microphone input (–) from microphone unit in front roof module (front left microphone for LHD vehicle)
11 FBAS wire (+) from reversing camera system control unit

12 pin C connector

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Analog input · ground (audio)
2 Analog input · right-side (audio)
3 USB (+5V)
4 USB (ground)
5 iPod (ACC power)
6 Detect
7 Analog input · left-side (audio)
8 Analog input · screen ground (audio)
9 FBAS wire (+)
10 FBAS wire (–)
11 iPod data
12 iPod data

4 pin display unit Connector

Audi A8 4H J794 display port. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (-)
2 LIN
3 LVDS(+)
4 ground

4 pin USB Connector

Audi A8 4H J794 external audio port. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D+
2 iPod detected
3 D-
4 ground
Audi (2011-2020) A6 RMC plus (LOW II) unit

Part numbers listed: 4G0035188EX, 4G0035188D

52-position main housing · block A

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block A is highlighted.
Cavity Function
A1 rear right speaker +
A2 front right speaker +
A3 front left speaker +
A4 rear left speaker +
A5 rear right speaker –
A6 front right speaker –
A7 front left speaker –
A8 rear left speaker –
A9 Subwoofer (+)
A10 Centre speaker (+)
A13 Subwoofer (-)
A14 Centre speaker (-)
A17 Ground (terminal 31)
A18 Permanent power (terminal 30)

52-position main housing · block B

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block B is highlighted.
Cavity Function
B1 Data from multimedia system operating unit
B2 RES BT multimedia system operating unit
B4 Microphone input (+) from microphone unit in front roofmodule, front left microphone
B7 Data to multimedia system operating unit
B8 Wake-up multimedia system operating unit
B9 Res HU to multimedia system operating unit
B12 Microphone input (–) from microphone unit in front roof module front left microphone

52-position main housing · block C

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block C is highlighted.
Cavity Function
C1 Analog input · ground (audio)
C2 Analog input · right-side (audio)
C3 USB (+5 V)
C4 USB (ground)
C6 Detect
C7 Analog input · left-side (audio)
C8 Analog input · screen ground (audio)
C9 FBAS wire (+)
C10 FBAS wire (–)
C11 iPod data
C12 iPod data

52-position main housing · block E

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block E is highlighted.
Cavity Function
E7 Ring-break diagnostics

4 pin light-brown connector

Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D (+)
2 iPod detected
3 D (–)
4 ground

4 pin purple connector

Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground
Audi (2011-2020) A6, S6, A7, S7 3G (3G+) High Satnav MMI Unit

Part numbers listed: 4G0035670

Audi’s 2012 A6 MMI Navigation Plus service drawing shows a 40-position J794 housing. The upper bank spans Audi blocks A and D.

40-position J794 housing · block A/D

Rear socket face, redrawn from the Audi A6 4G Navigation Plus service view. Table A1–A16 spans two service blocks, A (1–8) and D (9–16).
Cavity Function
A3 Wake-up to multimedia system operating unit
A5 Switch-on signal to telephone bracket / aerial am‐plifier for mobile telephone
A6 Res MU to multimedia system operating unit
A7 Ring-break diagnostics
A9 Switch-on signal to telephone bracket
A10 Data from multimedia system operating unit
A11 Data to multimedia system operating unit
A12 Ground (terminal 31)
A13 DIAG signal from telephone bracket
A14 Res BT from multimedia system operating unit
A15 Permanent power (terminal 30)

40-position J794 housing · block B

Rear socket face, redrawn from the Audi A6 4G Navigation Plus service view. The table numbers this insert locally from 1 to 12.
Cavity Function
B2 Microphone input (+) from front right microphone, microphone unit in front roof module
B3 Microphone input (-) from front right microphone, microphone unit in front roof module
B5 FBAS wire (-) from reversing camera system control unit
B8 Microphone input (+) from front left microphone, microphone unit in front roof module
B9 Microphone input (-) from front left microphone, microphone unit in front roof module
B11 FBAS wire (+) from reversing camera system control unit

40-position J794 housing · block C

Rear socket face, redrawn from the Audi A6 4G Navigation Plus service view. The table numbers this insert locally from 1 to 12.
Cavity Function
C1 Analog input · ground (audio)
C2 Analog input · right-side (audio)
C3 USB (+5 V)
C4 USB (ground)
C5 iPod, ACC power
C6 Detect
C7 Analog input · left-side (audio)
C8 Analog input · screen ground (audio)
C9 FBAS wire (+)
C10 FBAS wire (–)
C11 iPod data
C12 iPod data

4 pin yellow connector

Audi A6 4G MMI Navigation Plus J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D (+)
2 iPod detected
3 D (–)
4 ground

4 pin gray connector

Audi A6 4G MMI Navigation Plus J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground
Audi (2012-2016) A5, S5, A4, S4 MMI Navigation Head Unit

Part numbers listed: 8R1035746C, 8R1035746D, 8R1035746E, 8R1035746F, 8R1035746G, 8R1035746H, 8R1035746J ?

Connector identification. Audi’s A4 B8 J794 service drawing and the photographed 8R1-series rear panel show a 40-position main housing. The upper bank spans Audi blocks A and D. Verify microphone assignments for the steering and equipment configuration. Audi lists T12x pin 2 for right microphone positive on the documented LHD build, while the supplied reference lists pin 1.

40-position J794 housing · block A/D

Rear socket face, redrawn from the Audi A4 B8 Navigation service view. Table A1–A16 spans two service blocks, A (1–8) and D (9–16).
Cavity Function
A1 NF mute
A2 Voltage supply to multimedia system operating unit
A3 Wake-Up to multimedia system operating unit
A5 Switch-on signal to aerial amlifier for mobile telephone
A6 Res MU to multimedia system operating unit
A7 Ring-break diagnostics
A9 Switch-on signal to telephone bracket
A10 Data from multimedia system operating unit
A11 Data to multimedia system operating unit
A12 Ground (terminal 31)
A13 DIAG signal from telephone bracket
A14 Res BT from multimedia system operating unit
A15 Permanent power (terminal 30)
A16 ground to multimedia system operating unit

40-position J794 housing · block B

Rear socket face, redrawn from the Audi A4 B8 Navigation service view. The table numbers this insert locally from 1 to 12.
Cavity Function
B1 Microphone input (+) from microphone unit in front roof module (front right microphone )
B3 Microphone input (-) from microphone unit in front roof module (front right microphone )
B5 FBAS wire (-) from reversing camera system control unit
B8 Microphone input (+) from microphone unit in front roof module (front left microphone )
B9 Microphone input (-) from microphone unit in front roof module (front left microphone )
B11 FBAS wire (+) from reversing camera system control unit

40-position J794 housing · block C

Rear socket face, redrawn from the Audi A4 B8 Navigation service view. The table numbers this insert locally from 1 to 12.
Cavity Function
C1 Analog input · ground (audio)
C2 Analog input · right-side (audio)
C3 USB (+5 V)
C4 USB (ground)
C6 Detect
C7 Analog input · left-side (audio)
C8 Analog input · screen ground (audio)
C9 FBAS (+)
C10 FBAS (-)
C11 Ipod data
C12 Ipod data

4 pin light-brown connector (for external audio source)

Audi A4/A5 B8 MMI J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D (+)
2 iPod detected
3 D (–)
4 ground

4 pin grey connector (for display unit)

Audi A4/A5 B8 MMI J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.

Display pin 2 varies. T4al uses LIN on the documented configuration. Audi lists pin 2 as unused on the grey T4am configuration.

Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground
Audi (2013-2016) A3, S3, RS3 8V MMI unit

MOST unit (I8D), p/n 8V0035874B

52-position main housing · block A

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block A is highlighted.
Cavity Function
A1 rear right speaker +
A2 front right speaker +
A3 front left speaker +
A4 rear left speaker +
A5 rear right speaker –
A6 front right speaker –
A7 front left speaker –
A8 rear left speaker –
A9 Subwoofer (+)
A10 Centre speaker (+)
A13 Subwoofer (-)
A14 Centre speaker (-)
A17 Ground (terminal 31)
A18 Permanent power (terminal 30)

52-position main housing · block B

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block B is highlighted.
Cavity Function
B1 Microphone input (+) from microphone unit in front roof module (telephone microphone )
B4 NF (+) (audio) from pre-fitted components for mobile phone installation
B5 NF mute
B6 FBAS wire (-) from reversing camera system control unit
B7 Microphone input (–) from microphone unit in front roof module (telephone microphone)
B10 NF (-) (audio) from pre-fitted components for mobile phone installation
B12 FBAS wire (+) from reversing camera system control unit

52-position main housing · block C

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block C is highlighted.
Cavity Function
C1 Analog input · ground (audio)
C2 Analog input · right-side (audio)
C3 USB (+5 V)
C4 USB (ground)
C5 iPod, ACC power
C6 Detect
C7 Analog input · left-side (audio)
C8 Analog input · screen ground (audio)
C9 FBAS (+)
C10 FBAS (-)
C11 iPod data
C12 iPod data

52-position main housing · block E

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block E is highlighted.
Cavity Function
E1 CAN bus High to multimedia system operating unit / display unit for front information display and operating unit control unit
E2 Reset to multimedia system operating unit
E3 Ring-break diagnostics
E5 Switch-on signal to telephone bracket
E6 CAN bus High, infotainment
E7 CAN bus Low to multimedia system operating unit / display unit for front information display and operating unit control unit
E8 Reset from multimedia system operating unit
E11 Status signal from telephone bracket
E12 CAN bus Low, infotainment

4 pin brown connector

Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D (+)
2 iPod detected
3 D (–)
4 ground

4 pin purple connector for display unit

Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground
Audi (2013-2020) A6, S6, A7 RMC unit

Part numbers listed: 4G0035182H ??

52-position main housing · block A

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block A is highlighted.
Cavity Function
A1 rear right speaker +
A2 front right speaker +
A3 front left speaker +
A4 rear left speaker +
A5 rear right speaker –
A6 front right speaker –
A7 front left speaker –
A8 rear left speaker –
A9 Subwoofer (+)
A10 Centre speaker (+)
A13 Subwoofer (-)
A14 Centre speaker (-)
A17 Ground (terminal 31)
A18 Permanent power (terminal 30)

52-position main housing · block B

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block B is highlighted.
Cavity Function
B1 Data from multimedia system operating unit
B2 RES BT multimedia system operating unit
B7 Data to multimedia system operating unit
B8 Wake-up multimedia system operating unit
B9 Res HU to multimedia system operating unit

52-position main housing · block E

Rear socket face, redrawn from the Audi A6 4G RMC service view. Block E is highlighted.
Cavity Function
E7 Ring-break diagnostics

4 pin purple connector

Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground
Audi (2014-2017) A3 8V, S3 MMI Head Unit

Part numbers listed: 8V0035038B

52-position main housing · block A

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block A is highlighted.
Cavity Function
A1 rear right speaker +
A2 front right speaker +
A3 front left speaker +
A4 rear left speaker +
A5 rear right speaker –
A6 front right speaker –
A7 front left speaker –
A8 rear left speaker –
A9 Subwoofer (+)
A10 Centre speaker (+)
A13 Subwoofer (-)
A14 Centre speaker (-)
A17 Ground (terminal 31)
A18 Permanent power (terminal 30)

52-position main housing · block B

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block B is highlighted.
Cavity Function
B1 Microphone input (+) from microphone unit in front roof module (telephone microphone )
B4 NF (+) (audio) from pre-fitted components for mobile phone installation
B5 NF mute
B6 FBAS wire (-) from reversing camera system control unit
B7 Microphone input (–) from microphone unit in front roof module (telephone microphone)
B10 NF (-) (audio) from pre-fitted components for mobile phone installation
B12 FBAS wire (+) from reversing camera system control unit

52-position main housing · block C

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block C is highlighted.
Cavity Function
C1 Analog input · ground (audio)
C2 Analog input · right-side (audio)
C3 USB (+5 V)
C4 USB (ground)
C7 Analog input · left-side (audio)
C8 Analog input · screen ground (audio)

52-position main housing · block E

Rear socket face, redrawn from the Audi A3 8V J794 service view. Block E is highlighted.
Cavity Function
E1 CAN bus High to multimedia system operating unit / display unit for front information display and operating unit control unit
E2 Reset to multimedia system operating unit
E3 Ring-break diagnostics
E5 Switch-on signal to telephone bracket
E6 CAN bus High, infotainment
E7 CAN bus Low to multimedia system operating unit / display unit for front information display and operating unit control unit
E8 Reset from multimedia system operating unit
E11 Status signal from telephone bracket
E12 CAN bus Low, infotainment

4 pin light-brown connector (for external audio source)

Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D (+)
2 iPod detected
3 D (–)
4 ground

4 pin turquoise connector (for display unit)

Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground
Audi (2010-2018) A1 MMI Navi Head Unit

Part numbers listed: 8XA035192A (also for 8X0035183F, 8X0857273B, 8X0035183E?)

The Audi A1 RMC service manual identifies the CAN and MOST variant circuits as block E, T12w.

52-position main housing · block A

Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block A is highlighted.
Cavity Function
A1 rear right speaker +
A2 front right speaker +
A3 front left speaker +
A4 rear left speaker +
A5 rear right speaker –
A6 front right speaker –
A7 front left speaker –
A8 rear left speaker –
A9 Subwoofer in rear shelf
A10 Centre speaker
A13 Subwoofer in rear shelf
A14 Centre speaker
A17 Ground (terminal 31)
A18 Permanent power (terminal 30)

52-position main housing · block B

Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block B is highlighted.
Cavity Function
B4 Microphone input (+) from microphone unit in front roof module (telephone microphone ) (versions with MOST only)
B6 DIAG signal from telephone bracket
B12 Microphone input (–) from microphone unit in front roof module (telephone microphone) (versions with MOST only)

52-position main housing · block C

Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block C is highlighted.
Cavity Function
C1 Analog input · ground (audio)
C2 Analog input · right-side (audio)
C3 USB (+5 V)
C4 USB (ground)
C5 iPod (ACC power)
C6 USB Detect
C7 Analog input · left-side (audio)
C8 Analog input · screen ground (audio)
C9 FBAS wire (+)
C10 FBAS wire (–)
C11 iPod data
C12 iPod data

Block E · T12w CAN/MOST variant

Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block C is highlighted.
Cavity Function
E1 CAN Bus Low (Infotainment)
E7 CAN bus High (Infotainment) OR Ring-break diagnostics (versions with MOST only)
E12 Switch-on signal for telephone bracket /aerial amplifier for mobile telephone (versions with MOST only)

4-pin external media port

Audi A1 8X RMC service view, MOST equipment only. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 D (+)
2 iPod detected
3 D (–)
4 ground

4-pin display port

Audi A1 8X RMC service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity Function
1 LVDS (–)
2 LIN
3 LVDS (+)
4 ground

Amplifiers

Audi (2005-2008) A4, S4, RS4 amplifier

Part numbers listed: 8E5035223, 8E5035223D

23-pin amplifier connector

Amplifier socket, viewed from the mating side. The chamfered end is on the left and the middle row ends before the rightmost column.
Cavity Function
1 Right rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
2 Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
3 Left rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
9 Positive switched from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
14 Bass speaker (+)
15 Bass speaker (-)
17 speaker, left rear (+)
18 speaker, left rear (-)
20 speaker, right rear (+)
21 speaker, right rear (-)
22 Ground (terminal 31)
23 Permanent power (terminal 30)
Audi (2005-2008) A4, S4, RS4 BOSE Amplifier (32-pin)

Part numbers listed: 8E5035223B, 8E5035223C

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Bass speaker (+)
4 speaker, left rear (-)
5 speaker, right rear (+)
6 Positive switched from Radio R / Navigation System with CD Drive Control Module /Radio/Navigation Display Control Module
7 Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
13 Inside speaker (-)
14 Inside speaker (+)
15 Bass speaker (-)
16 speaker, left rear (+)
17 speaker, right rear (-)
19 Left front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
20 Right front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
21 Left rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
22 Right rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
26 speaker, right rear (-)
27 speaker, right rear (+)
29 Microphone input (+) from Inside Microphone
30 Microphone input (-) from Inside Microphone (-)
31 speaker, left rear (+)
32 speaker, left rear (-)
Audi (2005-2015) Q7 Basic amplifier

Part numbers listed: 4L0035223, 4L0910223

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Front left bass speaker (+)
4 Front right bass speaker (+)
6 Front left speaker (+)
7 Front right speaker (+)
8 Rear left speaker (+)
9 Rear right speaker (+)
10 Centre mid-range and treble speaker (+)
15 Front left bass speaker (–)
16 Front right bass speaker (–)
18 Front left speaker (–)
19 Front right speaker (–)
20 Rear left speaker (–)
21 Rear right speaker (–)
22 Centre mid-range and treble speaker (–)
23 Microphone 1 (+) from microphone unit in front roof module
25 NF (+) (audio) from pre-fitted components for mobilephone installation/Japan nav/China nav
27 Ring-break diagnostics
28 Microphone 1 (–) from microphone unit in front roof module
30 NF (–) (audio) from pre-fitted components for mobilephone installation/Japan nav/China nav
Audi (2006-2008) A4, S4, RS4 BOSE amplifier

Part numbers listed: 8H0035223, 8H0035223A

25-pin amplifier connector

BOSE amplifier socket, viewed from the mating side. The upper row is offset by half a contact pitch and the polarizing recess is at right.
Cavity Function
1 Inside speaker (+)
2 Inside speaker (-)
6 Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
7 Right rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
8 Left rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
9 Right front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
10 Left front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
11 Ground (terminal 31)
12 Permanent power (terminal 30)
14 Bass speaker (+)
15 Bass speaker (-)
16 speaker, left rear (-)
17 speaker, left rear (+)
18 speaker, right rear (+)
19 speaker, right rear (-)
20 speaker, left rear (+)
21 speaker, left rear (-)
22 speaker, right rear (+)
23 speaker, right rear (-)
25 Positive switched from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
Audi (2007-2014) TT BOSE amplifier

Part numbers listed: 8J0035223C, 8J0035223D

18-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
3 Signal (front left) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
4 Signal (front left) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
5 Signal (rear left) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
6 Signal (rear left) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
11 Signal (front right) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
12 Signal (front right) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
13 Signal (rear right) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
14 Signal (rear right) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Front left bass speaker (+)
4 Front right bass speaker (+)
5 Middle speaker (+)
6 Front right speaker (+)
7 Front left speaker (+)
8 Centre mid-range and treble speaker (+)
9 Microphone input (–) from microphone unit in front roof module
10 Microphone input (+) from microphone unit in front roof module
11 Rear left speaker (–)
12 Rear left speaker (+)
13 Rear right speaker (–)
14 Rear right speaker (+)
15 Front left bass speaker (–)
16 Front right bass speaker (–)
17 Middle speaker (–)
18 Front right speaker (–)
19 Front left speaker (–)
20 Centre mid-range and treble speaker (–)
23 Microphone input (screen ground) from microphone unit in front roof module
27 CAN Bus High (Infotainment)
29 Switched positive from radio / control unit with display for radio and navigation / navigation system with CD drive control unit
32 CAN Bus Low (Infotainment)
Audi (2007-2015) Q7 Bang&Olufsen amplifier

Part numbers listed: 4L0035466

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Centre mid-range and treble speaker (+)
4 Front left mid-range speaker (–)
5 Front right mid-range speaker (+)
6 Front left treble speaker (–)
7 Front right treble speaker (+)
8 Rear left treble speaker (–)
9 Rear right treble speaker (+)
11 Rear left mid-range speaker (+)
12 Rear left mid-range speaker (–)
13 Rear right mid-range speaker (+)
14 Rear right mid-range speaker (–)
15 Centre mid-range and treble speaker (–)
16 Front left mid-range speaker (+)
17 Front right mid-range speaker (–)
18 Front left treble speaker (+)
19 Front right treble speaker (–)
20 Rear left treble speaker (+)
21 Rear right treble speaker (–)
25 Microphone 1 (–) from microphone unit in front roof module
26 Microphone 2 (–) from microphone unit in front roof module (up to week 21/09)
27 Ring-break diagnostics
30 Microphone 1 (+) from microphone unit in front roof module
31 Microphone 2 (+) from microphone unit in front roof module (up to week 21/09)
32 Digital sound package control unit 2

J525 secondary 32-pin connector · T32f

J525 connector C / T32f, mating face in Audi drawing A91-0983. The upper row starts at pin 1 on the left.
Cavity Function
8 NF (–) (audio) from Japan nav/pre-fitted componentsfor mobile phone installation (up to week 21/09)
9-16 Digital sound package control unit 2
24 NF (+) (audio) from Japan nav/pre-fitted componentsfor mobile phone installation (up to week 21/09)
25-32 Digital sound package control unit 2
Audi (2007-2015) Q7 BOSE amplifier

Part numbers listed: 4L0035223

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Front right speaker (–)
4 Front right speaker (+)
5 Front right bass speaker (+)
6 Front left bass speaker (+)
7 Front left speaker (–)
8 Front left speaker (+)
9 Microphone 1 (–) from microphone unit in front roof module
10 Microphone 1 (+) from microphone unit in front roof module
11 Rear right mid-range speaker (–)
12 Rear right mid-range speaker (+)
13 Rear left mid-range speaker (–)
14 Rear left mid-range speaker (+)
15 Middle speaker (–)
16 Middle speaker (+)
17 Front right bass speaker (–)
18 Front left bass speaker (–)
19 Rear right speaker (–)
20 Rear right speaker (+)
21 Rear left speaker (–)
22 Rear left speaker (+)
23 Microphone 1 (screen) from microphone unit in front roofmodule
24 Microphone 2 (–) from microphone unit in front roof module(up to week 21/09)
25 Microphone 2 (+) from microphone unit in front roof module (up to week 21/09)
29 Ring-break diagnostics
30 NF (–) (audio) from pre-fitted components for mobile phone installation/Japan nav/China nav (up to week 21/09)
31 NF (+) (audio) from pre-fitted components for mobile phone installation/Japan nav/China nav (up to week 21/09)
Audi (2008-2011) A5,A4,Q5 Bang&Olufsen Amplifier (with CAN)

Part numbers listed: 8T0035223AP, 8T0035223AJ

18-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Microphone input 1 (+) (internal microphone)
2 Microphone input 1 (screen ground) (internal microphone)
3 Microphone input 2 (+) (voice command microphone, up to 2008)
4 Signal (+), rear right from radio
5 Signal (+), rear left from radio
6 Signal (+), front right from radio
7 Signal (+), front left from radio
9 CAN Bus High (infotainment)
10 Microphone input 1 (–) (internal microphone)
13 Signal (–), rear right from radio
14 Signal (–), rear left from radio
15 Signal (–), front right from radio
16 Signal (–), front left from radio
18 CAN Bus Low (infotainment)

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Rear left speaker (+)
4 Rear right speaker (+)
5 Centre mid-range and treble speaker (+)
6 Front left speaker (+)
7 Front right speaker (+)
8 Rear left mid-range speaker (+)
9 Rear right mid-range speaker (+)
10 Front right bass speaker (+)
15 Rear left speaker (–)
16 Rear right speaker (–)
17 Centre mid-range and treble speaker (–)
18 Front left speaker (–)
19 Front right speaker (–)
20 Rear left mid-range speaker (–)
21 Rear right mid-range speaker (–)
22 Front right bass speaker (–)
23 Front left bass speaker (+)
25 Subwoofer in rear shelf (+)
28 Front left bass speaker (–)
30 Subwoofer in rear shelf (–)
Audi (2008-2016) Q5, A5, RS5 amplifier (CAN)

Part numbers listed: 8T0035223AH

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Subwoofer in Rear Shelf (+)
4 Left Front Speaker (+)
5 Right Front Speaker (+)
6 Left Rear Speaker (+)
7 Right Rear Speaker (+)
8 Center Mid-Treble Speaker (+)
13 CAN Bus high (Infotainment)
14 CAN Bus low (Infotainment)
15 Subwoofer in Rear Shelf (-)
16 Left Front Speaker (-)
17 Right Front Speaker (-)
18 Left Rear Speaker (-)
19 Right Rear Speaker (-)
20 Center Mid-Treble Speaker (-)
23 Right Rear Signal (+) from Radio
24 Left Rear Signal (+) from Radio
25 Right Front Signal (+) from Radio
26 Left Front Signal (+) from Radio
28 Right Rear Signal (-) from Radio
29 Left Rear Signal (-) from Radio
30 Right Front Signal (-) from Radio
31 Left Front Signal (-) from Radio
Audi (2010-2015) A4, A5, Q5 Bang&Olufsen Amplifier (with MOST)

Part numbers listed: 8T1035223A

18-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Microphone input 1 (+) (internal microphone)
2 Microphone input 1 (screen ground) (internal microphone)
3 Microphone input 2 (+) (voice command microphone, up to 2008)
4 NF (+) from pre-fitted components for mobile phone installation (up to 2008)
6 Analog input · right side from connection for external audio sources (up to 2008)
7 Analog input · left side from connection for external audio sources (up to 2008)
10 Microphone input 1 (-) (internal microphone)
11 Microphone input 2 (screen ground) (voice command microphone, up to 2008)
12 Microphone input 2 (-) (voice command microphone, up to 2008)
13 NF (-) from pre-fitted components for mobile phone installation (up to 2008)
15 Analog input · ground, right side from connection for external audio sources (up to 2008)
16 Analog input · ground, left side from connection for external audio sources (up to 2008)
17 Ring-break diagnostics

32-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Rear left speaker (+)
4 Rear right speaker (+)
5 Centre mid-range and treble speaker (+)
6 Front left speaker (+)
7 Front right speaker (+)
8 Rear left mid-range speaker (+)
9 Rear right mid-range speaker (+)
10 Front right bass speaker (+)
15 Rear left speaker (–)
16 Rear right speaker (–)
17 Centre mid-range and treble speaker (–)
18 Front left speaker (–)
19 Front right speaker (–)
20 Rear left mid-range speaker (–)
21 Rear right mid-range speaker (–)
22 Front right bass speaker (–)
23 Front left bass speaker (+)
25 Subwoofer in rear shelf (+)
28 Front left bass speaker (–)
30 Subwoofer in rear shelf (–)
Audi (2011-2014) A8, S8 Bang&Olufsen Amplifier

Part numbers listed: 4H0035465, 4H0035465A, 4H0035465B

32-pin connector · J525 T32h

A8 4H J525 T32h, mating face in Audi drawing A91-11593. Pin 1 is at the lower right.
Cavity Function
1 Digital sound package control unit 2
2 Digital sound package control unit 2
3 Digital sound package control unit 2
4 Digital sound package control unit 2
5 Digital sound package control unit 2
6 Centre left microphone (+)
7 Centre right microphone (+)
8 Rear left microphone (+)
9 Microphone unit in front roof module ( internal mi‐
10 Rear right microphone (+)
11 Screen ground
12 Engine speed signal from engine control unit (+)
13 n/c
14 Digital sound package control unit 2
15 n/c
22 Centre left microphone (-)
23 Centre right microphone (-)
24 Rear left microphone (-)
25 Microphone unit in front roof module - R164- ( internal mi‐
26 Rear right microphone (-)
27 n/c
28 Engine speed signal from engine control unit (-)
29 Ring-break diagnostics
30 Digital sound package control unit 2
31 n/c

38-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 Front left mid-range speaker (+)
4 Front right mid-range speaker (+)
5 Rear left mid-range speaker (+)
6 Rear right mid-range speaker (+)
7 Centre speaker (+)
8 Centre speaker 2 (+)
9 Rear left treble speaker 2 (+)
10 Rear right treble speaker 2 (+)
15 Front left mid-range speaker (-)
16 Front right mid-range speaker (-)
17 Rear left mid-range speaker (-)
18 Rear right mid-range loudspeake (-)
19 Centre speaker (-)
20 Centre speaker 2 (-)
21 Rear left treble speaker 2 (-)
22 Rear right treble speaker 2 (-)
23 Front left treble speaker (+)
24 Front right treble speaker (+)
25 Rear left treble speaker (+)
26 Rear right treble speaker (+)
27 Left effect speaker (+)
28 Right effect speaker (+)
31 Front left treble speaker (-)
32 Front right treble speaker (-)
33 Rear left treble speaker (-)
34 Rear right treble speaker (-)
35 Left effect speaker (-)
36 Right effect speaker (-)
Audi (2011-2018) A6, A7, RS6, RS7 Bang&Olufsen Amplifier

Part numbers listed: 4G1035465, 4G1035465A, 4G1035465B

38-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
5 Front left mid-range speaker (+)
6 Front right mid-range speaker (+)
7 Centre speaker (+)
8 Centre speaker 2 (+)
9 Left effect speaker (+)
10 Right effect speaker (+)
17 Front left mid-range speaker (–)
18 Front right mid-range speaker (–)
19 Centre speaker (–)
20 Centre speaker 2 (–)
21 Left effect speaker (–)
22 Right effect speaker (–)
23 Front left treble speaker (+)
24 Front right treble speaker (+)
25 Rear left treble speaker (+)
26 Rear right treble speaker (+)
31 Front left treble speaker (–)
32 Front right treble speaker (–)
33 Rear left treble speaker (–)
34 Rear right treble speaker (–)

J525 secondary 32-pin connector · T32e

A6 4G J525 T32e, mating face in Audi drawing A91-11593. Pin 1 is at the lower right.
Cavity Function
1 Digital sound package control unit 2
2 Digital sound package control unit 2
3 Digital sound package control unit 2
4 Digital sound package control unit 2
5 Digital sound package control unit 2
6 Centre left microphone (+)
7 Centre right microphone (+)
8 Rear left microphone (+)
9 Microphone unit in front roof module, internal microphone (+)
10 Rear right microphone (+)
11 Screen ground
12 Engine speed signal from engine control unit (+)
14 Digital sound package control unit 2
16 Digital sound package control unit 2
17 Digital sound package control unit 2
18 Digital sound package control unit 2
19 Digital sound package control unit 2
20 Digital sound package control unit 2
21 Digital sound package control unit 2
22 Centre left microphone (–)
23 Centre right microphone (–)
24 Rear left microphone (–)
25 Microphone unit in front roof module, internal microphone (–)
26 Rear right microphone (–)
28 Engine speed signal from engine control unit (–)
29 Ring-break diagnostics
30 Digital sound package control unit 2
32 Digital sound package control unit 2
Audi (2012-2017) A6, S6, A7, A8, S8, RS6, RS7 BOSE Amplifier

Part numbers listed: 4G0035223C

38-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
3 rear right speaker +
4 Front left bass speaker (+)
5 Subwoofer (–)
7 Front left mid-range speaker (–)
8 Front right mid-range speaker (+)
9 Front right treble speaker (–)
10 Front left treble speaker (+)
11 Front right bass speaker (–)
12 Front right bass speaker (+)
13 rear left speaker +
14 rear left speaker –
15 rear right speaker –
16 Front left bass speaker (–)
17 Subwoofer (+)
19 Front left mid-range speaker (+)
20 Front right mid-range speaker (–)
21 Front right treble speaker (+)
22 Front left treble speaker (–)
25 Ring-break diagnostics
28 Screen ground from microphone unit in front roof module, internal microphone
29 Microphone unit in front roof module, internal microphone (–)
30 Microphone unit in front roof module, internal microphone (+)
31 Centre speaker (+)
32 Centre speaker (–)
33 Left effect speaker (–)
34 Left effect speaker (+)
37 Right effect speaker (+)
38 Right effect speaker (–)

18-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
6 Rear left microphone (+)
7 Rear left microphone (–)
8 Rear right microphone (+)
9 Rear right microphone (–)
10 Engine speed signal from engine control unit (+)
11 Engine speed signal from engine control unit (–)
13 Centre right microphone (+)
14 Centre right microphone (–)
16 Centre left microphone (+)
17 Centre left microphone (–)
Audi (2014-2022) A3 8V, S3, RS3 Bang&Olufsen amplifier

Part numbers listed: 81A035466B, 81A035466, 8V0035412C, 8V0035412, 8V0035416, 8V0035454, 8V0035397, 8V0035399C

38-pin amplifier connector

End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity Function
1 Permanent power (terminal 30)
2 Ground (terminal 31)
4 Rear left bass speaker (+)
5 Rear left bass speaker (-)
6 Centre speaker (-)
7 Front left bass speaker (-)
8 Front left bass speaker (+)
9 Front right bass speaker (+)
10 Front right bass speaker (-)
11 Front left mid-range speaker (–)
12 Front left mid-range speaker (+)
13 Front right mid-range speaker (–)
14 Front right mid-range speaker (+)
16 Rear right bass speaker (–)
17 Rear right bass speaker (+)
18 Centre speaker (+)
19 Subwoofer (–)
20 Subwoofer (+)
21 Subwoofer (+)
22 Subwoofer (–)
23 Front right treble speaker (–)
24 Front left treble speaker (–)
25 Rear left treble speaker (+)
26 Rear right treble speaker (+)
27 Right effect speaker (–)
28 Left effect speaker (–)
29 Microphone input (-) from microphone unit in front roof module, internal microphone
31 Front right treble speaker (+)
32 Front left treble speaker (+)
33 Rear left treble speaker (–)
34 Rear right treble speaker (–)
35 Right effect speaker (+)
36 Left effect speaker (+)
37 Microphone input (+) from microphone unit in front roof module, internal microphone
38 Ring-break diagnostics

CD changer

Audi (2005-2015) CD Changer

Part numbers listed: 8E0057111D

12-pin CD changer connector

CD changer 8E0057111D socket face. The two lower locating tabs match the connector illustration.
Cavity Function
1 CD data out to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
2 CD CLK out to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
3 Ground from Radio R /terminal 31 (with RNS-E/radio generation II+)
4 CD data in from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
6 Permanent positive from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
7 Right signal to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
8 Positive switched from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
9 Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
10 Left signal to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module

Chorus

Audi TT/TTS 8J · Chorus II+ EU (8J0 035 152 G)

Part 8J0 035 152 G. Audi identifies this suffix as Chorus II+ for the 8J TT family. The drawings follow the photographed Chorus rear socket and the matching label layout. The connector label marks C10 as AU PL and D16 as DI SENS. Their electrical details are unspecified.

FuseA15263748D913101411151216B123456789101112C123456789101112
Chorus II+ connector in the factory label orientation (rotated 180°).

A · front speakers

Chorus II+ socket viewed from the rear of the radio · block A.
Cavity Function
2 Right front speaker +
3 Left front speaker +
6 Right front speaker −
7 Left front speaker −

B · CD changer, AUX and BOSE coding

Chorus II+ socket viewed from the rear of the radio · block B.
Cavity Function
1 AUX left input
2 SDI/CD audio ground
3 AUX audio ground
4 Permanent +12 V supply for CD changer
5 BOSE coding
6 CD changer data out
7 AUX right input
8 SDI/CD left audio input
9 SDI/CD right audio input
10 CD changer switching line (switch symbol on label)
11 CD changer data in
12 CD changer clock

C · line outputs, telephone and diagnostics

Chorus II+ socket viewed from the rear of the radio · block C.
Cavity Function
3 Front left line output
5 Rear left line output
6 Telephone audio −
7 K-line diagnostics (K-LTG)
8 Line-output ground
9 Front right line output
10 AU PL (as marked on the label)
11 Rear right line output
12 Telephone audio +

D · power, CAN and control

Chorus II+ socket viewed from the rear of the radio · block D.
Cavity Function
9 Infotainment CAN high
10 Infotainment CAN low
11 Telephone mute
12 Ground
13 DSP enable
14 Alarm line (DWA)
15 Permanent +12 V battery supply
16 DI SENS (as marked on the label)
Audi (2010-2014) A1, S1 Chorus Head Unit

Part numbers listed: 8X0035160

Variant check. The reference lists A4 and A8 as negative speaker circuits with inconsistent channel pairing. Those two assignments require a factory wiring check.

Block A

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
A1 speaker (+) (rear right)
A2 speaker (+) (front right)
A3 speaker (+) (front left)
A4 Assignment requires confirmation
A6 speaker (–) (front right)
A7 speaker (–) (front left)
A8 Assignment requires confirmation
A9 CAN Bus High (Infotainment)
A10 CAN Bus Low (Infotainment)
A12 Ground (terminal 31)
A15 Permanent power (terminal 30)
A16 Permanent live connected to PIN 15 (anti-theft alarm)

Block C

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
C6 NF– (audio) from telephone transmitter and receiver unit
C9 Signal (front right) to digital sound package control unit
C10 NF mute (audio)
C12 NF + (audio) from telephone transmitter and receiver unit
Audi (2010-2017) A4, A5, Q5 Chorus III Head Unit

Part numbers listed: 8R2057152

16 pin connector A (brown and black plugs)

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 RR+ · Right rear speaker (+)
2 FR+ · Right front speaker (+)
3 LF+ · Left front speaker (+)
4 LR+ · Left rear speaker (+)
5 RR- · Right rear speaker (-)
6 FR- · Right front speaker (-)
7 LF- · Left front speaker (-)
8 LR- · Left rear speaker (-)
9 CAN H · CAN Bus high (Infotainment)
10 CAN L · CAN Bus low (Infotainment)
11 DISP_P · Power Supply to Front Information Display Control Head
12 GND · Ground (terminal 31)
13 D_CAN · CAN Bus (Display) to the Front Information Display Control Head
14 D_CAN · CAN Bus (Display) to the Front Information Display Control Head
15 Batt · Permanent power (terminal 30)

12 pin B connector (blue plug)

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Left LF · Left LF-In from the External Audio Source Connection
2 LF GND · LF-In ground from the External Audio Source Connection
3 Ground · Ground
4 Batt+ · Permanent positive
6 DATA OUT
7 Right LF · Right LF-In from the External Audio Source Connection
8 Left · Left signal
9 Right · Right signal
10 ACC+ · Positive switched
11 DATA IN
12 CLK

12 pin C connector (green plug)

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Microphone IN (-)
2 Right LF OUT
3 LF OUT ground
4 Microphone OUT (-)
5 Left LF IN (-)
6 LF (-) · from the cell phone preparation/ Telephone Transceiver
7 Microphone IN (+)
8 Left LF OUT
9 Microphone OUT (+)
10 LF mute · wire from preliminary setup for cell phone preparation
11 Left LF IN (+)
12 LF (+) · from the cell phone preparation/ Telephone Transceiver

Concert

Audi (2002-2008) Concert 2 CD RS4, A6 Head Units

Part numbers listed: 4B0035186H, 4B0057186Q, 4B0035186G, 8N0035186B, 4B0035186Q

A connector (black)

B12345678A12345678910785634121234567891011121314151617181920DC
Radio-side 46-pin ISO reference, with block A highlighted.
Cavity Function
1 BOSE coding to ground (only with BOSE)
2 Anti-theft warning system ground from Comfort System Central Control Module
3 L-diagnostic
7 Permanent power (terminal 30)
8 Ground (terminal 31)

B connector (brown)

B12345678A12345678910785634121234567891011121314151617181920DC
Radio-side 46-pin ISO reference, with block B highlighted.
Cavity Function
3 Right front speaker (+) (not with BOSE)
4 Right front speaker (-) (not with BOSE)
5 Left front speaker (+) (not with BOSE)
6 Left front speaker (-) (not with BOSE)

C connector (black)

B12345678A12345678910785634121234567891011121314151617181920DC
Radio-side 46-pin ISO reference, with block C highlighted.
Cavity Function
1 Left rear signal to Amplifier
2 Right rear signal to Amplifier
3 Signal ground to Radio
4 Left front signal to Amplifier (only with BOSE)
5 Right front signal to Amplifier (only with BOSE)
6 Positive switched to Amplifier
7 CAN-Bus High (Infotainment)
10 CD ground to CD Changer
12 CAN-Bus Low (Infotainment)
13 CD data in from CD Changer
14 CD data out to CD Changer
15 CD CLK from CD Changer
16 Permanent positive to CD Changer
17 Positive switched to CD Changer
18 CD ground to CD Changer
19 Left signal from CD Changer
20 Right signal from CD Changer

D connector (red)

B12345678A12345678910785634121234567891011121314151617181920DC
Radio-side 46-pin ISO reference, with block D highlighted.
Cavity Function
1 NF mute from Telephone Transceiver /preliminary setup for cell phone package
3 NF (+) from Telephone Transceiver (not with Nav IV)/preliminary setup for cell phone package
4 NF (-) from Telephone Transceiver (not with Nav IV)/preliminary setup for cell phone package
5 NF (+) from Navigation System with CD Drive Control Module (only with Nav IV)
6 NF (-) from Navigation System with CD Drive Control Module (only with Nav IV)
7 Navigation control wire from Navigation System with CD Drive Control Module (only with Nav IV)
Audi A4 B7 · Concert Solo (8E0 035 186 AK)

Part 8E0 035 186 AK · Blaupunkt 7 646 136 380. The socket and connector-label views follow the photographed unit. The label marks C10 as AU PL and D16 as DI SENS. Their electrical details are unspecified.

FuseA15263748D913101411151216B123456789101112C123456789101112
Concert Solo connector in the factory label orientation (rotated 180°).

A · front speakers

Concert Solo socket viewed from the rear of the radio · block A.
Cavity Function
2 Right front speaker +
3 Left front speaker +
6 Right front speaker −
7 Left front speaker −

B · CD changer, AUX and BOSE coding

Concert Solo socket viewed from the rear of the radio · block B.
Cavity Function
1 AUX left input
2 SDI/CD audio ground
3 AUX audio ground
4 Permanent +12 V supply for CD changer
5 BOSE coding
6 CD changer data out
7 AUX right input
8 SDI/CD left audio input
9 SDI/CD right audio input
10 CD changer switching line (switch symbol on label)
11 CD changer data in
12 CD changer clock

C · line outputs, telephone and diagnostics

Concert Solo socket viewed from the rear of the radio · block C.
Cavity Function
3 Front left line output
5 Rear left line output
6 Telephone audio −
7 K-line diagnostics (K-LTG)
8 Line-output ground
9 Front right line output
10 AU PL (as marked on the label)
11 Rear right line output
12 Telephone audio +

D · power, CAN and control

Concert Solo socket viewed from the rear of the radio · block D.
Cavity Function
9 Infotainment CAN high
10 Infotainment CAN low
11 Telephone mute
12 Ground
13 DSP enable
14 Alarm line (DWA)
15 Permanent +12 V battery supply
16 DI SENS (as marked on the label)
Audi (2008-2012) A4 B8 Concert Head Unit

Part numbers listed: 8T2035186Q, 8R1035186Q, 8T1035186B

Connector block A

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
A1 RR+ · Right rear speaker (+)
A2 RF+ · Right front speaker (+)
A3 LF+ · Left front speaker (+)
A4 LR+ · Left rear speaker (+)
A5 RR- · Right rear speaker (-)
A6 RF- · Right front speaker (-)
A7 LF- · Left front speaker (-)
A8 LR- · Left rear speaker (-)
A9 CAN-H · CAN bus high (Infotainment)
A10 CAN-L · CAN bus low (Infotainment)
A12 GND · Ground (terminal 31)
A15 BAT+ · Permanent power (terminal 30)
A16 Permanent positive (not used)

12 pin B connector

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
B1 Left LF IN+ · Left IN for the external audio source connection
B2 LF GND · LF for the external audio source connection ground
B7 Right LF IN · Right IN for the external audio source connection

12 pin C connector

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
C2 Right LF OUT
C3 LF OUT ground
C4 Microphone OUT (-)
C5 Left LF IN (-)
C6 LF (-) · from Telephone Transceiver
C7 Microphone IN (+)
C8 Left LF OUT
C9 Microphone OUT (+)
C10 LF mute
C11 Left LF IN (+)
C12 LF (+) · for the telephone transceiver

10 pin Front Information Display Connector

Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.
Cavity Function
1 Voltage Supply
2 Ground
3 n/c
4 Diag. Display
5 Cable Diag
6 LVDS OUT (+)
7 LVDS OUT (-)
8 LVDS OUT ground
9 Diag T0
10 Diag T1
Audi (2008-2014) TT Single CD Concert Radio

Part numbers listed: 8J0035186A, 8J0035186G, 8J0035186P, 8J0035186R

Connector block A

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
A2 speaker (+) (front right) · only with basic sound system
A3 speaker (+) (front left)
A6 speaker (–) (front right)
A7 speaker (–) (front left)
A9 CAN Bus High (Infotainment)
A10 CAN Bus Low (Infotainment)
A11 NF mute (audio) from prefitted components for mobile phone installation
A12 Ground (terminal 31)
A13 Switched positive to digital sound package control unit
A15 Permanent power (terminal 30)
A16 Permanent live connected to PIN 15 (anti-theft alarm)

Connector block B

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
B1 Analog input · left-side (audio)
B2 Signal ground to CD changer / iPod holder
B3 Analog input · ground (audio)
B4 Permanent live to CD changer / iPod holder
B5 BOSE coding to terminal 31 · only with BOSE
B6 Data output to CD changer / iPod holder
B7 Analog input · right-side (audio)
B8 Signal (left-side) from CD changer / iPod holder
B9 Signal (right-side) from CD changer / iPod holder
B10 Switched positive to CD changer / iPod holder
B11 Data input from CD changer / iPod holder
B12 CLK (clock) from CD changer / iPod holder

Connector block C

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
C3 Signal (front left) to digital sound package control unit
C5 Signal (rear left) to digital sound package control unit
C6 NF– (audio) from telephone transmitter and receiver unit
C8 Signal ground to digital sound package control unit
C9 Signal (front right) to digital sound package control unit
C11 Signal (rear right) to digital sound package control unit
C12 NF + (audio) from telephone transmitter and receiver unit
Audi (2010-2016) A4, A5, RS5, Q5 Concert III Head Unit

Part numbers listed: 8T1 035 186R ?

16 pin connector A (brown and black plugs)

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 RR+ · Right rear speaker (+)
2 FR+ · Right front speaker (+)
3 LF+ · Left front speaker (+)
4 LR+ · Left rear speaker (+)
5 RR- · Right rear speaker (-)
6 FR- · Right front speaker (-)
7 LF- · Left front speaker (-)
8 LR- · Left rear speaker (-)
9 CAN H · CAN Bus high (Infotainment)
10 CAN L · CAN Bus low (Infotainment)
12 GND · Ground (terminal 31)
15 Batt · Permanent power (terminal 30)

12 pin B connector (blue plug)

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Left LF · Left LF-In from the External Audio Source Connection
2 LF GND · LF-In ground from the External Audio Source Connection
3 Ground · Ground
4 Batt+ · Permanent positive
6 DATA OUT
7 Right LF · Right LF-In from the External Audio Source Connection
8 Left · Left signal
9 Right · Right signal
10 ACC+ · Positive switched
11 DATA IN
12 CLK

12 pin C connector (green plug)

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Microphone IN (-)
2 Right LF OUT
3 LF OUT ground
4 Microphone OUT (-)
5 Left LF IN (-)
6 LF (-) · from the cell phone preparation/ Telephone Transceiver
7 Microphone IN (+)
8 Left LF OUT
9 Microphone OUT (+)
10 LF mute · wire from preliminary setup for cell phone preparation
11 Left LF IN (+)
12 LF (+) · from the cell phone preparation/ Telephone Transceiver

10 pin Front Information Display Connector

Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.
Cavity Function
1 Voltage Supply
2 Ground
3 n/c
4 Diag. Display
5 Cable Diag
6 LVDS OUT (+)
7 LVDS OUT (-)
8 LVDS OUT ground
9 Diag T0
10 Diag T1

Displays

Audi (2002-2017) Multimedia Information Display Unit

Part numbers listed: 8F0919604, 8R0919604, 4F0919604, 4L0919604, 4F0919604X, 8R0919604A

T8ai · separate display power

87654321
Audi workshop view of the J685 power socket. Cavity 1 is at the right end.
Cavity Function
4 Battery supply, terminal 30
5 Ground, terminal 31

T4an / T4ao · display link

3241
Audi workshop view. Cavity 1 is lower right and cavity 2 is upper right.
Cavity Function
1 LVDS negative
2 LIN for the documented A4 B8 configuration
3 LVDS positive
4 Ground

Confirm pin 2 against the exact display part number and build. Some later listings show ground at this position.

Audi (2009-2016) MMI Information Screen 10 pin connector

Part numbers listed: 8T0057603E, 8T0057603F, 8T0057603A, 8T0057603G, 8T0919603F, 8T0919603G, 8T0919603A, 8T0919603E

T10w · Concert / Symphony display

Black 10-pin connector for the J685 display paired with the Concert or Symphony radio. Check the connector ID before wiring. The red Chorus T10u and the MMI Basic T10t have their own assignments.

Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.
11029384756
Alternate orientation in the connector reference. Pin 1 is upper left. Match the moulded numbers before comparing the two views.
Cavity Function
1 Power supply from radio
2 Ground
3 Unassigned
4 Display diagnostics
5 Cable diagnostics
6 LVDS positive
7 LVDS negative
8 LVDS ground
9 Diagnostic T0
10 Diagnostic T1

Radio tuner

Audi (2010-2014) A4, S4, A5,A6, Q5, Q7 Radio Receiver Tuner Module

Part number 4G0035082. This section uses the Audi Q5 MMI Radio R service view. Verify equipment and build-specific assignments against the fitted receiver.

Audi numbers the two power terminals above the fuse area as 41 and 42. Some listings refer to them as 17 and 18 within the combined upper bank.

Block A · T8ag

Radio-side view, redrawn from Audi A91-11740. Block A is highlighted. The numbers are the positions on the full housing.
Cavity Function
1 Rear right speaker (+)
2 Front right speaker (+)
3 Front left speaker (+)
4 Rear left speaker (+)
5 Rear right speaker (−)
6 Front right speaker (−)
7 Front left speaker (−)
8 Rear left speaker (−)

Block D · T16ag

Radio-side view, redrawn from Audi A91-11740. Block D is highlighted. The numbers are the positions on the full housing.
Cavity Function
9 Rear-shelf subwoofer
10 Centre mid/treble speaker
11 Ring-break diagnostics
13 Rear-shelf subwoofer
14 Centre mid/treble speaker
41 Ground, terminal 31
42 Battery positive, terminal 30

Block B · T12w

Radio-side view, redrawn from Audi A91-11740. Block B is highlighted. The numbers are the positions on the full housing.
Cavity Function
17 Left audio input
18 Audio input ground
19 Audio input diagnostics
21 Audio diagnostics
22 Telephone low-frequency signal (−)
23 Right audio input
24 Audio input shield ground
27 Telephone audio shield ground
28 Telephone low-frequency signal (+)

Block C

Radio-side view, redrawn from Audi A91-11740. Block C is highlighted. The numbers are the positions on the full housing.
Cavity Function
29 Headphone output 1 diagnostics
31 Headphone outputs 1 and 2 diagnostics
34 Headphone output 2 diagnostics
35 Headphone output 1 left
36 Headphone output 1 ground
37 Headphone output 1 right
38 Headphone output 2 left
39 Headphone output 2 ground
40 Headphone right output. Verify the channel against the fitted equipment diagram.

Symphony

Audi Symphony II · Panasonic 46-position ISO radio

Panasonic service-manual coverage includes CQ-EA1070L through CQ-EA1074L and CQ-EA1060L through CQ-EA1063L. Documented examples include A4 8E0 035 195, A8 4D0 035 195 H and A6 4B0 035 195 H. This section uses Panasonic's A–D markings. The Audi workshop manual calls the same positions I–IV.

The Panasonic diagram lists a powered antenna output on C5. Some Audi A4 vehicle-side diagrams leave that cavity unassigned. Front speaker outputs on B are used on direct-drive configurations. BOSE uses the external amplifier.

A / I · 20-way audio, CAN and CD changer

Panasonic Symphony II socket face · block A · viewed from the rear of the radio.
Cavity Function
1 Rear left line output
2 Rear right line output
3 Line-output ground
4 Front left line output
5 Front right line output
6 Switched amplifier output
7 Infotainment CAN high
10 CD changer ground
12 Infotainment CAN low
13 CD changer data in
14 CD changer data out
15 CD changer clock
16 Permanent +12 V supply for CD changer
17 CD changer control output
18 CD changer audio ground
19 CD changer left audio input
20 CD changer right audio input

B / II · 8-way speakers

Panasonic Symphony II socket face · block B · viewed from the rear of the radio.
Cavity Function
3 Right front speaker +
4 Right front speaker −
5 Left front speaker +
6 Left front speaker −

C / III · 8-way power and diagnostics

Panasonic Symphony II socket face · block C · viewed from the rear of the radio.
Cavity Function
1 BOSE coding input
2 Alarm ground
3 K-line diagnostics
5 Powered antenna output + (Panasonic radio-side assignment)
7 Permanent +12 V battery supply
8 Ground

D / IV · 10-way telephone and navigation

Panasonic Symphony II socket face · block D · viewed from the rear of the radio.
Cavity Function
1 Telephone mute
3 Telephone / navigation audio input +
4 Telephone / navigation audio input −
5 Navigation audio input +
6 Navigation audio input −
7 Navigation audio control

Panasonic’s CQ-JA1070L–CQ-JA1074L service manual identifies those models as Concert radios.

A6 C5 Symphony II SDARS · 4B0 035 195 N

Panasonic CQ-EA1362L. The redraw follows the rear socket of the photographed 4B0 035 195 N unit. The tables list the radio-side positions documented in the 2004 A6 C5 Symphony service material. The front speaker positions are for direct-drive configurations. The SDARS tuner has a separate connector. Use the vehicle-specific wiring diagram to identify any additional BOSE or satellite-radio circuits.

SDARS · A / I · audio, CAN and CD changer

A6 C5 Symphony II SDARS socket face · block A · viewed from the rear of the radio.
Cavity Function
1 Rear left line output
2 Rear right line output
3 Line-output ground
6 Switched positive for active speaker / amplifier
7 Infotainment CAN high
10 CD changer ground
12 Infotainment CAN low
13 CD changer data in
14 CD changer data out
15 CD changer clock
16 Permanent +12 V supply for CD changer
17 Switched CD changer supply
18 CD changer audio ground
19 CD changer left audio
20 CD changer right audio

SDARS · B / II · direct-drive front speaker positions

A6 C5 Symphony II SDARS socket face · block B · viewed from the rear of the radio.
Cavity Function
3 Right front speaker +
4 Right front speaker −
5 Left front speaker +
6 Left front speaker −

SDARS · C / III · power and diagnostics

A6 C5 Symphony II SDARS socket face · block C · viewed from the rear of the radio.
Cavity Function
2 Anti-theft alarm ground
3 Onboard diagnostic line
7 Permanent +12 V battery supply (terminal 30)
8 Ground (terminal 31)

SDARS · D / IV · telephone and navigation

A6 C5 Symphony II SDARS socket face · block D · viewed from the rear of the radio.
Cavity Function
1 Telephone mute
3 Telephone audio + (vehicles without navigation)
4 Telephone audio − (vehicles without navigation)
5 Navigation audio +
6 Navigation audio −
7 Navigation control
Audi (2005-2008) RS4 and others Symphony II+ Head Unit

Part numbers listed: 8P0057195PX

A connector

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
2 Right front speaker (+) (not with BOSE)
3 Left front speaker (+) (not with BOSE)
6 Right front speaker (-) (not with BOSE)
7 Left front speaker (-) (not with BOSE)
9 CAN-Bus High (Infotainment)
10 CAN-Bus Low (Infotainment)
11 NF mute from preliminary setup for cell phone preparation
12 Ground (terminal 31)
13 Positive switched to Amplifier/Woofer (in left rear luggage compartment) / Amplifier R12
15 Permanent power (terminal 30)
16 Permanent positive connected with PIN 15 (anti-theft warning system)

B connector (blue)

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
2 CD ground to CD Changer
4 Permanent positive to CD Changer
5 BOSE coding to ground (only with BOSE)
6 CD data out to CD Changer
8 Left signal from CD Changer
9 Right signal from CD Changer
10 Positive switched to CD Changer
11 CD data in from CD Changer
12 CD CLK from CD Changer

C connector

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
3 Left front signal to Amplifier (only with BOSE)
5 Left rear signal to Amplifier/Woofer (in left rear luggage compartment) / Amplifier
6 NF (-) from Telephone Transceiver/preliminary setup for cell phone package
8 Signal ground to Amplifier/Woofer (in left rear luggage compartment) / Amplifier
9 Right front signal to Amplifier (only with BOSE)
11 Right rear signal to Amplifier/Woofer (in left rear luggage compartment) / Amplifier
12 NF (+) from Telephone Transceiver /preliminary setup for cell phone package
Audi (2007-2017) Symphony Head Unit

Part numbers listed: 8T1035195AA ?

16 pin connector A (brown and black plugs)

Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 RR+ · Right rear speaker (+)
2 FR+ · Right front speaker (+)
3 LF+ · Left front speaker (+)
4 LR+ · Left rear speaker (+)
5 RR- · Right rear speaker (-)
6 FR- · Right front speaker (-)
7 LF- · Left front speaker (-)
8 LR- · Left rear speaker (-)
9 CAN H · CAN Bus high (Infotainment)
10 CAN L · CAN Bus low (Infotainment)
12 GND · Ground (terminal 31)
15 Batt · Permanent power (terminal 30)

12 pin B connector (blue plug)

Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Left LF · Left LF-In from the External Audio Source Connection
2 LF GND · LF-In ground from the External Audio Source Connection
3 Ground · Ground
4 Batt+ · Permanent positive
6 DATA OUT
7 Right LF · Right LF-In from the External Audio Source Connection
8 Left · Left signal
9 Right · Right signal
10 ACC+ · Positive switched
11 DATA IN
12 CLK

12 pin C connector (green plug)

Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity Function
1 Microphone IN (-)
2 Right LF OUT
3 LF OUT ground
4 Microphone OUT (-)
5 Left LF IN (-)
6 LF (-) · from Telephone Transceiver
7 Microphone IN (+)
8 Left LF OUT
9 Microphone OUT (+)
10 LF mute
11 Left LF IN (+)
12 LF (+) · from Telephone Transceiver

10 pin Front Information Display Connector

Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.
Cavity Function
1 Voltage Supply
2 Ground
3 n/c
4 Diag. Display
5 Cable Diag
6 LVDS OUT (+)
7 LVDS OUT (-)
8 LVDS OUT ground
9 Diag T0
10 Diag T1

TV tuner

Audi (2007-2013) A3, TT, TTS TV Tuner

Part numbers listed: 8J0919148, 8J0919148A, 8J0919148B, 8J0919148C

R78 TV tuner · T54a 54-pin connector

373839404142434445464748495051525354192021222324252627282930313233343536123456789101112131415161718
Tuner-side socket viewed into the mating face. Housing details follow the 8J0919148A rear-panel reference. The Audi 54-way service view places 1–18 on the lower row, 19–36 in the middle and 37–54 on top.
Cavity Function
2 CAN Bus Low (Infotainment)
3 CAN Bus High (Infotainment)
4 Audio screen (front) to navigation system with CD drive control unit
5 Audio output (front right) to navigation system with CD drive control unit
7 Audio output (front left) to navigation system with CD drive control unit
9 Screen ground (front) to navigation system with CD drive control unit
10 Video screen (front) to navigation system with CD drive control unit
11 Video output (Sync., front ) to navigation system with CD drive control unit
12 Video ground to navigation system with CD drive control unit
13 Video output (blue, front ) to navigation system with CD drive control unit
14 Video ground to navigation system with CD drive control unit
15 Video output (green, front ) to navigation system with CD drive control unit
16 Video ground to navigation system with CD drive control unit
17 Video output (red, front ) to navigation system with CD drive control unit
19 Ground (terminal 31)
20 Permanent power (terminal 30)
53 Ext. video ground AV1
54 I/0 pin

Legacy equipment

  • Audi (2000-2001) Navigation PLUS II Head Unit · Blaupunkt Audi Navigation D2, p/n 4D0 035 192 N
  • Audi Beta CC · AUZ1Z2 (4A0 035 152) by Blaupunkt 7 640 846 080
  • Audi Beta CC Autoreverse · AUZ1Z2 (4A0 035 152) by Blaupunkt 7 640 846 080
  • Audi Beta II
  • Audi Chorus (Blaupunkt)
  • Audi Chorus (Grundig)
  • AUDI Chorus, Concert
  • Audi Concert AUZ5Z3
  • Audi Concert CQ-LA1923L
  • Audi Concert PLUS
  • Audi Concert US
  • Audi Delta, Delta CC, Delta CC AUZ1Z4, Delta CC US AUZ1Z6
  • Audi Gamma car audio connector
  • Audi Gamma CC · p/n 4A0 035 186
  • Audi Gamma CC
  • Audi Gamma CC Bose
  • Audi Gamma III (M327)
  • Audi Gamma S
  • Audi Navigation (2002-2006) disc unit · p/n 4B0 919 887 A, 4B0 919 887 AX, 4B0 919 887 E, 4B0 919 887 EX, 4B0 919 887 C, 4B0 919 887 CX, 4B0 919 887 D, 4B0 919 887 DX
  • Audi Symphony CQ-JA1920L, CQ-JA1924L Head Units
  • Audi Symphony EU TT
  • Audi Symphony HE303
  • Audi Symphony I

Legacy connector faces and circuit assignments await verification.